CRG Discussion Forum
Camaro Research Group Discussion => Originality => Topic started by: rick-68 on March 12, 2006, 03:07:44 PM
-
I have a 68 rs . Can,t seem to find the correct air filter housing assembly for non smog and with auto trans.. I think it has a vent elbow for right side v/cover and no heat stove and thermo valve. I NEED YOUR HELP PLEASE!!!!
-
It should have a left side manifold heat stove with elbow pipe to the air cleaner.
-
It should have a left side manifold heat stove with elbow pipe to the air cleaner.
Left side? Left = driver's side, Right = passenger side.
-
thanks johnZ,, Do you know where I may find one of these.. In any condition??? Thanks Rick PS, In the assembly manual they list two air housing #s They both show no heat stoves? The #s are--6983655 & 6484221.. my car is LA built #1295TH built First week of sept w/powerglide
-
Heat stove was on the left (drivers) side in 68. Moved to the right side in 69.
-
In the course of trying to find the correct air cleaner for my '69RS base coupe, I collected a couple of others, one may be a '68. I have at least 3 dfferent variants hanging on the wall in the garage. If you can e-mail me with the details, I'll compare to what I have and can send you pics as well.
Let me know.
Richard
-
This isn't the best photo of the setup but does show the 327/275hp air cleaner and stove pipe. The manifold stove and the stove pipe are the tough ones to find.
-
It looks like the one that CCARGO HAS. Call me any time after 5:30 pm my # 440-266-0554 ... I 'm interested ... THANKS RICK.................
In the course of trying to find the correct air cleaner for my '69RS base coupe, I collected a couple of others, one may be a '68. I have at least 3 dfferent variants hanging on the wall in the garage. If you can e-mail me with the details, I'll compare to what I have and can send you pics as well.
Let me know.
Richard
-
Will check tonight and get back to you tomorrow.
Richard
-
Air cleaner that I have that I believe is a '68 is smaller in heighth than the one you have. I believe it is for the base 210 Hp configuration which would have had a Rochester 2BBl with 1-1/4" throttle plates.
Sorry I wasn't able to help.
Richard
-
Hay,, thanks for the effort Rich,, I'll have to keep looking for that NEEDLE IN A HAY STACK..........Thanks Rick...
Air cleaner that I have that I believe is a '68 is smaller in heighth than the one you have. I believe it is for the base 210 Hp configuration which would have had a Rochester 2BBl with 1-1/4" throttle plates.
Sorry I wasn't able to help.
Richard
-
If anyone out there knows anybody that has such a filter housing. Please contact here or e-mail at rmmcsween@sbcglobal.net or Call (440)266-0554 Ohio....... Thanks ......
-
If anyone out there knows anybody that has such a filter housing. Please contact here or e-mail at rmmcsween@sbcglobal.net or Call (440)266-0554 Ohio....... Thanks ......
Rick,
I don't have a spare, ...but am following this thread since I also have a '68 327/275 auto.
My question however, ...wouldn't the air filter housing be the same (with auto trans) for a 350(SS) and the 327/275, ...since both had Q-jet carbs? (with the exception of the chrome lid for an SS)?
-
That's correct, the L48 and L30 are very similar in many regards....just a little more bling ;)
-
I might as well add a shot of my 68 L35 with A/C to cover the bases. It gets alot more crowded and complicated with a BB, A/C, and smog ::)
-
Nice photos ;), ...I was actually looking for some shots of a 396 with the AIR intact :)
-
I"m still looking for that NEEDLE IN THE HAY STACK ( AIR FILTER HOUSING). Please contact if anybody has one Thanks Rick.................................