61
General Discussion / Re: POMONA, CA. 50th Annual Winter Nationals, Feb 2010
« on: January 05, 2010, 08:39:27 PM »
Glad you are going Jerry. They will love your car! 
News:
Welcome to the CRG Discussion Forum!
Classified ads are not allowed on the forum.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
62
General Discussion / Re: Why is there some Z28's with 3908326 Rear Proportioning Valves and Some without
« on: December 26, 2009, 01:01:25 PM »
1969 Z/28 (11D-1968) has no valve. Still has original brakes lines.
64
Originality / gas cap
« on: December 03, 2009, 06:25:33 PM »
Does anybody have a picture of an original (assembly line) gas cap for a 69 Z/28, nova etc.? Thanks, Sam
65
Maintenance / Re: 302 with close ratio steering box, finding right headers?
« on: December 02, 2009, 09:55:35 PM »
Hooker SuperComps fit fine. Had them for years. Jegs or Summit.
66
Originality / Re: valve cover grommets 350 and 302 motors
« on: October 21, 2009, 04:49:50 PM »
How about the PCV valves? Assembly line different that the OTC ones. I have a couple I believe to be assembly line originals and neither say AC Delco Spark Pug on them. Are they one piece steel or two piece with the seam in the middle? Any pictures? I am refering to a 69 350/300 motor. Thanks, Sam
67
General Discussion / Re: '67 Z28 At Cecil County
« on: October 15, 2009, 09:40:28 PM »
And man does it H O O K!
68
Originality / Re: valve cover grommets 350 and 302 motors
« on: October 15, 2009, 09:35:49 PM »
I purchased a real old set of covers. Look to be 69 vintage and the grommets are hardned. The one on the drivers side is an angle type while the other is round. Maybe changed real early on or different venders? Thanks for the answer. See you at the Dutch! Sam
69
Originality / valve cover grommets 350 and 302 motors
« on: October 15, 2009, 06:32:05 PM »
Is the rubber gromet on the drivers side (PCV valve) angle cut or round like the other side? Also assembly line PCV valve, does it have AC Spark Plug on it or just something like AC 105? The PCV valve also had a D underneath on the plunger that moves. Thanks, Sam
70
Mild Modifications / Re: lightweight flywheel in a 69Z
« on: September 28, 2009, 12:01:41 AM »
That is a pretty good first gear. You may get away with it. I would try it because of the 4.10's too.
71
Maintenance / Re: Smoke from Oil Breather Filter
« on: September 27, 2009, 11:59:04 PM »It doesn't seem to be consuming much oil. It seems to be missing at idle and under load. I should add that a found a loose spark plug cable on the Drivers side but after I pushed it in there was no change. And the smoke is coming from the opposite side of the engine.maybe that one plug is fouled on the drivers side and that is your problem. Change that one plug out for now and see what happens.
Utah67
72
General Discussion / Re: Big Win @ Maryland Int'l Raceway
« on: September 27, 2009, 11:54:21 PM »
Good going Jerry! Much deserved!
73
General Discussion / Re: Stahl Headers anyone? pix please?
« on: June 29, 2009, 02:42:09 AM »
Go with the Hooker Super Comps. They fit perfect! Sam
74
General Discussion / Re: anyone know who manufactures the 67-68 Z28 reproduction headers?
« on: April 07, 2009, 11:49:08 AM »
The Super Comps work fine! Why give yourself a headache?
75
General Discussion / Re: Adjusting rocker clearance on 30-30 cam.
« on: April 07, 2009, 11:44:46 AM »
We set .026/.026 cold with roller tip rockers and have no problems. I idle the car at about 1000 rpm's and still stop pretty easy.