Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Springer Tom

Pages: [1] 2 3
1
General Discussion / Re: 50 Z/28's For Sale ???
« on: December 27, 2012, 12:17:29 AM »
Could have at least put the temperature sending unit on the correct side :P :P :P :P :P

2
General Discussion / Re: This Car Has "Wrong" Written All Over It.
« on: December 16, 2012, 10:49:21 PM »
I don't know, guys, this cat says he has been to EVERY car auction........ ::)

3
Originality / '69 Driveshaft question
« on: October 01, 2012, 12:56:35 AM »
I have read I need a 49 9/16" driveshaft for my '69 with 350/Turbo 350 and 12 bolt.A friend has one 49" and yoke just under 5". Can I use this and change the yoke to one of the 5.5" ones? Thanks ???

4
Maintenance / Re: Opinion needed-engine/tranny first or front end?
« on: September 04, 2012, 03:44:43 PM »
Thanks guys

5
Maintenance / Re: '69 horn wiring
« on: September 03, 2012, 02:37:12 PM »
Well that explains it, I should be used to this crap by now >:(who has the correct ones?

6
Maintenance / Re: '69 horn wiring
« on: September 03, 2012, 12:32:20 PM »
Yeah Steve, I got all that, but the spring and contact don't fit in the sleeve when you put the little grommet with the wires in it....for now I left the contact pin out, I 'm wondering if the contact is too long....

7
Maintenance / Opinion needed-engine/tranny first or front end?
« on: September 03, 2012, 01:33:37 AM »
Had to remove the right front fender and skirt, bumper, grille,valance, etc to install A/C box....seems to me it would be easy to remove radiator support,put engine and tranny together on the floor and slide them right in, then put the sheetmetal back on.....chime right in please

8
Maintenance / '69 horn wiring
« on: September 03, 2012, 01:27:40 AM »
Could someone please explain how the 2 wires from the horn buttons on a '69 2 spoke wheel connect to the column? I have a spring and a metal button also.....this car is making me dumb :o

9
Maintenance / Re: '69 blower fan replacement
« on: September 03, 2012, 01:25:30 AM »
Yeah, pulled the fender and skirt, etc. wasn't too bad, had it all apart in about 45 minutes,thanks fellas

10
Originality / Dumb questions about interior rear side panels...
« on: August 28, 2012, 12:56:38 AM »
I didn't take my '69 apart so I don't know what missing if anything. Is there anything that attached the rear panel to the car? Right now it just hangs there....are there supposed to be armrests? Hard to believe that the rear seat holds it in by itself..... ???

11
Maintenance / '69 blower fan replacement
« on: August 22, 2012, 01:13:26 AM »
Could someone tell me the simple way to replace the blower fan? My car was painted and the front end put on without the A/C box and blower fan installed. Chassis manual says pull lower fender out 6"!!!! after loosening the rear skirt bolts. Don't mind spending the time but didn't want to take the fender off unless I had to......thanks guys

12
Originality / Re: Color for horn relay & e-brake brackets
« on: August 17, 2012, 09:45:00 PM »
Yes the ones attached to the leaf spring mounting plates

13
Originality / Color for horn relay & e-brake brackets
« on: August 17, 2012, 09:06:23 PM »
Need the colors for horn relay and the 2 rear emergency brake cable brackets......thanks

14
Originality / '69 TH350 shifter mounting hardware
« on: July 29, 2012, 02:31:19 PM »
There are some big holes in the floor of my car where the shifter gets mounted, about 7/16".....what is the correct hardware? Thanks

15
General Discussion / Re: Poor quality reproduction crap....
« on: July 29, 2012, 02:18:14 PM »
OK, thanks for the info....where are the triangular reinforcements located?

Pages: [1] 2 3
anything