Messages

31

Restoration / speedometer cable

« on: May 19, 2008, 08:42:18 PM »

Does any know the correct length of a speedometer cable for a 1967 Camaro 396 4 speed?  Thanks in advance.

32

Restoration / 67 camaro rear glass

« on: May 18, 2008, 01:11:27 AM »

Help!   I am in need of a clear rear window, date coded, for my 67 camaro. I am on my fourth glass with no luck.  Two were arched wrong and did not fit, the other two fit great, but the glass had staining in the glass. appeared to be between the layers.  Any help would be appreciated.  thanks in advance.  Pete

33

Restoration / Re: camaro two piece rotors

« on: May 13, 2008, 10:40:56 PM »

thanks for the input. the two sets we picked up at carlisle, only two has the three holes in them. someone at carlisle said that was for cooling, I don't think so.  I would believe for balancing before I would believe cooling.  thanks.  Pete

34

Restoration / camaro two piece rotors

« on: April 27, 2008, 12:59:11 AM »

I read the articles on the two piece rotors posted earlier. I was lucky enough to pick up two sets at spring carlisle this weekend.  Question, is there a difference between the 67's and the ones used on the 68-69 cars.  I was told that the 67's had holes drilled in the hat area to cool the bearings.  Are they interchangable and what do I need for on my 67 restoration project.  thanks Pete

35

Restoration / Re: 1967 camaro front rotors

« on: April 06, 2008, 04:21:38 PM »

Thanks very much.  With that info the set I was looking at is no good.  Does anybody have a set for sale?

36

Restoration / 1967 camaro front rotors

« on: April 06, 2008, 01:44:01 PM »

Does anyone know the min. thickness for original two piece front rotors for a 1967 camaro?

37

Restoration / Re: Wheel lip mldgs needed

« on: January 13, 2008, 10:35:28 PM »

I received e-mail from the gentleman on e-bay. all are gm, two have scratches from not being in a wrapper, and current bid is $330.  they go off in three hours.  thanks for the info.  Pete

38

Restoration / Re: Wheel lip mldgs needed

« on: January 13, 2008, 02:29:21 PM »

Thanks Paul.  I e-mailed seller to question damages on the rear ones.  Were these aniodized aluminum or stainless?  Don't know if you could polish aniodozed aluminum.  Pete

39

Restoration / Wheel lip mldgs needed

« on: January 13, 2008, 12:54:08 AM »

My son and I are restoring a 67 bb #'s matching camaro. We have located about everything we need regarding date coding. We are in need of  wheel lip mouldings.  Prefer not using aftermarket.  Any help will be greatly appreciated.  Pete

40

Restoration / interior trim

« on: December 31, 2007, 12:52:20 AM »

I am restoring a numbers matching 67 bb camaro. I have seen one car that had what appears to be an anodized aluminum trim that ran along the headliner on both sides from quarter window to windshield. Was this standard with the deluxe interior? Is this available. thanks in advance  Pete

41

Restoration / Re: Correct exhaust clamps

« on: December 31, 2007, 12:49:02 AM »

thanks guys.  I went to the website and the clamps are as close to original as you will find.  thanks again  Pete

42

Restoration / Re: Where to buy "correct appearing" ball joints?

« on: December 31, 2007, 12:29:21 AM »

Restoring our 67 camaro, we purchased rivit head bolts for installing the upper ball joints. they look like a rivit, and bolt from under.  We purchased them from "Trim Tag.com"  These were for the "vett"  guys.  Pete

43

Restoration / Re: Correct exhaust clamps

« on: December 27, 2007, 03:09:44 PM »

The clamps you received from Ames?  Where is Ames?  How do I go about getting these clamps and what are they listed as

44

Restoration / horn relay

« on: December 17, 2007, 10:38:27 PM »

What is the correct part number for the horn relay on a 1967 camaro?

45

Restoration / Re: trunk latch

« on: December 17, 2007, 10:34:50 PM »

thank you, that is i figured